- Fits standard 5- and 6-inch recessed cans.
- No rewiring required—uses an E26 adapter.
- Rated load up to 44 lb.
- Includes a 7.48-inch flush ceiling trim.
- Package includes conversion hardware and cable lock.
Why Convert a Recessed Can to a Pendant?
A pendant instantly adds aim, character, and layered light to a flat ceiling. If you already have a 5- or 6-inch recessed can, a conversion kit lets you hang a pendant without opening drywall or running new wires. With Jolux’s kit, you can go from “builder-basic” to “custom look” in one afternoon—ideal for renters and DIYers who want high impact with minimal disruption. The kit is designed for 5/6-inch recessed cans and installs quickly, no electrician required.
What You Need (Kit + Tools)
- Jolux 5/6" Recessed Can Light Conversion Kit (includes cover trim, adapter hardware, and an E26 socket adapter).
- Your pendant fixture and shade.
- Ladder, screwdriver, voltage tester, tape measure.
- Optional: cable stop/lock for fine height tuning (the kit includes hardware to secure the cord).
Safety First
- Turn power off at the breaker and verify with a non-contact tester.
- Confirm your can is 5" or 6" standard size.
- Check pendant weight against the kit’s 44 lb load rating.
- If your ceiling box/can shows damage, consult a licensed pro.
Step-by-Step: Install the Jolux Conversion Kit
1) Remove the old trim and bulb
Lower the existing can trim and unscrew the bulb. Keep any loose springs clear of the opening.
2) Add the E26 adapter
Screw the E26 adapter into the can’s socket (hand-tight). This provides power to your new pendant.
3) Anchor the conversion hardware
Use the kit’s internal support pieces to anchor inside the can (elastic clips / clamping plate / threaded rod assemblies depending on variant). Tighten until snug; don’t overtighten thin sheet-metal cans.
4) Set cord height & strain relief
Feed the pendant cord through the cover plate and integrated strain relief/cable lock so the weight is carried by the kit’s structure—not the socket.
5) Mount the 7.48" cover trim
Press the trim flush to the ceiling; this hides blemishes around the can opening for a clean finish.
6) Power on & test
Restore power at the breaker. Check on/off, dimming, and that the canopy is flush with no wobble.
Pro Tips: Height, Aim, and CCT
- Pendant height: Kitchen island 30–36" from countertop; entry/traffic ≥7' clear headroom.
- Glare control: If you see hot spots on walls, raise the pendant or use a diffused shade.
- Color temperature (CCT): 2700K = cozy evenings; 3000K = crisp neutrals; 4000K = task-forward or gallery moments.
- Dimming: Use a compatible dimmer for LED bulbs, or pair with a smart bulb for scenes.
Style Ideas: Kitchen, Entry, Reading Nook
- Entry focal pendant: Replace a can by the door with a smoked-glass globe for instant character.
- Reading corner: A small metal drum over a lounge chair anchors the nook and frees floor space.
- Kitchen island: Convert two adjacent cans into twin pendants, matching finishes to pulls.
Troubleshooting & Compatibility
- Pendant too heavy? Weigh fixture + shade + accessories; must be ≤ 44 lb.
- Ceiling gap / rough cutout? The 7.48" trim is forgiving; add a thin foam gasket if your ceiling is textured.
- Flicker while dimming? Use quality LED bulbs and a compatible wall dimmer; avoid mixing legacy halogens with LEDs on the same circuit.
- Outdoor location? Ensure the pendant itself is rated for the location and your ceiling assembly is protected.
FAQs
Does the kit fit both 5" and 6" cans?
Yes—designed for standard 5/6-inch recessed cans.
Do I need to rewire?
No—use the included E26 adapter to power your pendant without new wiring.
What’s the max load?
Up to 44 lb under normal installation conditions.
Will it cover imperfect openings?
Yes—the 7.48-inch trim hides most rough edges around the can opening.
Can I use it on a sloped ceiling?
Yes, but confirm the pendant’s canopy and cord allow hanging plumb.
Cost & Time: DIY vs Hiring
DIY: 1 kit + pendant + bulbs; the first unit may take 30–60 minutes; subsequent units are much quicker. Pro install: Consider for heavy fixtures, mixed wiring, or damaged cans.
